http://schema.org/InStock

OLED Display 0,96" Zoll I2C 128x64Pixel blaugelb SSD1306 kompatibel zu Arduino und Raspberry Pi

Marke:
Produktcode: 0711906114028
Verfügbar: 36

6,99€
Ohne Steuer: 5,87€

- +

Das 0,96 Zoll OLED I2C Display hat eine Auflösung von 128x64 Pixels. Es ist kontrastreich und kann dank des integrierten Display-Controllers SSD1306 mit nur vier Verbindungen direkt mit dem I2C-Bus verbunden werden. Das Display verfügt über die innovative OLED Technologie. OLEDs benötigen keine aufwändige Hintergrundbeleuchtung, wie etwa LCD-Displays. Bei OLEDs werden die Pixel direkt zum Leuchten angeregt. Durch Umlöten des "Adress-Widerstands" (4,7kΩ) auf der Rückseite, kann das Display von der Adresse 0x3C auf die Adresse 0x3D umgestellt werden. Lassen Sie sich nicht davon beirren, dass dort die Adressen 0x78 und 0x7A aufgedruckt sind. Für den Arduino müssen Sie die Adressen durch 2 teilen. So können Sie 2 Displays parallel betreiben, ohne einen zusätzlichen I2C-Multiplexer einzusetzen.

Auf der Registerkarte Downloads finden Sie mehrere Beispiel-Sketches für den Arduino und weitere technische Dokumentation.

Wir bieten diese monochromen Displays in den Farben weiß, blau, und gelb-blau an. Bitte beachten Sie, dass das gelb-blaue Display zwischen den beiden Farbbereichen eine Lücke von einem Pixel Höhe hat.

Zur Programmierung des 0,96 Zoll OLED I2C Displays benötigen Sie die beiden Libraries Adafruit SSD1306 und Adafruit GFX, sowie die Wire-Librarie für die I2C-Schnittstelle die Sie über die Arduino-Software herunterladen und installieren können.

Lieferumfang:

1 Stück 0,96 Zoll OLED I2C Display Farbe: blaugelb

Hinweis: Der 4polige Steckverbinder liegt bei, ist aber nicht eingelötet. Sie könnten also alternativ auch einen gewinkelten Stecker oder Kabel einlöten. 

 

Abbildungen ähnlich. Es kann, je nach Fertigungslos, Abweichungen in der Farbigkeit, Bestückung, Maßen und Beschriftung geben.

WEEE-Registrierungsnummer: DE33880481

Spezifikationen:

Controller SSD1306
Interface I2C
Pinbelegung GND (1), VCC (2), SCL (3), SDA (4)
Pixelfarbe blaugelb
Blickwinkel >160°
Bildschirmdiagonale 0,96" = 24,4mm
Auflösung 128x64 Pixels
Pixelgröße 0.152×0.152 mm
Betriebsspannung 3,3V - 5V
Stromaufnahme kleiner 11mA - 0,055W (bei 5V)
Betriebstemperatur

-20°C bis +70°C

Gewicht <4g
Abmessungen ca. 27mm x 27mm x 4,2mm (ohne Stecker)

 

The 0.96 inch OLED I2C display has a resolution of 128x64 pixels. It is high-contrast and can be connected directly to the I2C bus with just four connections thanks to the integrated display controller SSD1306. The display features innovative OLED technology. OLED doesn't need an elaborate backlight like some LCD displays. With OLEDs, the pixels are directly stimulated to light up. By resoldering the "address resistor" (4,7kΩ, Pos R11 to R12) on the back, the display can be switched from address 0x3C to address 0x3D. Don't be misled by the fact that the addresses 0x78 and 0x7A are printed there. For the Arduino you need to divide the addresses by 2. This allows you to operate 2 displays in parallel without using an additional I2C multiplexer.

See the Downloads tab for several sample Arduino sketches and other technical documentation.

We offer these monochrome displays in the colors white, blue, yellow and yellow-blue. Please note that the yellow-blue display has a gap of one pixel in height between the two color areas.

To program the 0.96 inch OLED I2C display, you need the two libraries Adafruit SSD1306 and Adafruit GFX and the Wire-library for the I2C interfacewhich you can download and install using the Arduino software.

Scope of delivery:

1 piece 0.96 inch OLED I2C display color: yellow-blue

Note: The 4-pin connector is included but not soldered. You could alternatively solder in an angled plug or cable. 

 

Similar pictures. Depending on the production lot, there may be deviations in colour, assembly, dimensions and labeling.

WEEE-Registernumber: DE33880481

Spezifikationen:

Controller SSD1306
Interface I2C
Pinout GND (1), VCC (2), SCL (3), SDA (4)
Pixelcolor yellow-blue
Viewing angle >160°
Screen size 0,96" = 24,4mm
Resolution 128x64 Pixels
Pixelsize 0.152×0.152 mm
Operating voltage 3,3V - 5V
Power consumption less 11mA - 0,055W (at 5V)
Operating temperatur -20°C to +70°C
Weight <4g
Dimensions ca. 27mm x 27mm x 4,2mm (without plug)

net4web 0.96 inch OLED I2C display

Datenblatt deutsch

Datasheet english

 

Sketches für Arduino - Sketches for Arduino:

Displaytest mit verschiedenen Grafiken - Display test with different graphics

Logo als Startbildschirm - Logo as start screen

Textausgabe auf OLED 0,96" 128x64px - Text output on OLED 0,96" 128x64px

 

Tipps & Tricks:

Eigene Grafiken für Arduino und OLED-Displays erstellen

Create your own graphics for Arduino and OLED displays

 

Konformitätserklärungen - Declarations of Conformity:

RoHS-Konformitätserklärung - RoHS-Declaration of Conformity

Es gibt keine Bewertungen für dieses Produkt.
Eine Rezension schreiben
Bestätigungscode *

Dieses Formular ist durch Aimy Captcha-Less Form Guard geschützt

Facebook-Kommentar
Wir benutzen Cookies

Wir nutzen Cookies auf unserer Website. Einige von ihnen sind essenziell für den Betrieb der Seite, während andere uns helfen, diese Website und die Nutzererfahrung zu verbessern (Tracking Cookies). Sie können selbst entscheiden, ob Sie die Cookies zulassen möchten. Bitte beachten Sie, dass bei einer Ablehnung womöglich nicht mehr alle Funktionalitäten der Seite zur Verfügung stehen.